|
|
|
DPMS Flip Up Rear Sight
The Patented Mangonel™ Front Flip Up Sight uses an aluminum base with steel legs and a steel clamp for durability and strength. This sight unit uses an A2 front sight. A large hex head knob is easily manipulated to loosen or tighten the clamp. The sight is designed to fit on the Mil-Std 1913 Picatinny accessory rail. The front sight has three positions: down (1st position), 2nd position for use on gas blocks, and a 3rd position when both the front sight and rear sight are on the same rail. The whole sight weighs only 3.8 ounces. It is a good companion for the EOTech Holographic's Sight or other optics.
|
|
|
|
|
|
|
DPMS Flip Up Front Sight
The Patented Mangonel™ Front Flip Up Sight uses an aluminum base with steel legs and a steel clamp for durability and strength. This sight unit uses an A2 front sight. A large hex head knob is easily manipulated to loosen or tighten the clamp. The sight is designed to fit on the Mil-Std 1913 Picatinny accessory rail. The front sight has three positions: down (1st position), 2nd position for use on gas blocks, and a 3rd position when both the front sight and rear sight are on the same rail. The whole sight weighs only 3.8 ounces. It is a good companion for the EOTech Holographic's Sight or other optics.
|
|
|
|
|
|
|
DPMS Front & Rear Flip Up Sight Set
Kit contains both the Front and the Rear Mangonel sights.
|
|
|
|
|
|
|
Triple High Rail Detachable Rear Sight
A combination of a Tri-Rise riser with a rear A2 adjustable sight assembly. This High Rail system is approximately 1/2" higher than the Low Rail series. This allows you to attach an optic to the top of the rail and other rail-mounted accessories such as flashlights and lasers.
Made from 6000 Series heat-treated aluminum.
|
|
|
|
|
|
|
Triple Low Rail Detachable Rear Sight
A combination of a Tri-Rise riser with a rear A2 adjustable sight assembly. Featuring Picatinny style rails on the top, left and right of the riser. This allows you to attach an optic to the top of the rail to be in coaxial line of sight with the rear sight assembly and also allows you to attach other rail-mounted accessories to the side of the riser.
Made from 6000 Series heat-treated aluminum.
|
|
|
|
|
|
|
Detachable Rear Sight
Attaches to various flattop upper receivers. Designed using the Picatinny rail system. Aluminum and steel construction. Height of sight will line up with standard front sights.
300 meters of elevation and intended as backup iron sight only.
Made by DPMS
|
|
|
|
|
|
|
Detachable Carry Handle
Carry handle designed to attach to AR flattop upper receivers. Allows for use of the iron sights. Easily installed and removed.
|
|
|
|
|
|
|
Tactical Latch
For use with the A-15/EM-16 and LR-308 series rifles. Replaces the charging handle latch, allows easy function of rifle with either hand. A must for the tactical or scoped flattop rifles. Charging handle not included.
Latch only.
|
|
|
|
|
|
|
Ambidextrous Safety Selector Switch
Three Piece Design. (With Screw) Replaces the Standard Selector for Safe and Fire from Either Side of the Receiver. Will not fit M16.
|
|
|
|
|
|
|
Bull Barrel Front Sight
.936 Diameter Holes for Mounting to Bull Barrels. Attaches to the Barrel with 1 Set Screw (Included)
Pre Ban Banonet Lug
|
|
|
|
|
|
|
Detachable Front Sight
Includeds: Post, Detent, and Spring
|
|
|
|
|
|
|
Single Rail Gas Block
Single Rail Picatinny Rail on top of Gas Block. (.750 Diameter)or (.936 Diameter) Select Barrel Size Below
|
|
|
|
|
|
|
Bull Barrel Gas Block
Aluminum Gas Block fits DPMS Standard Barrels or any Barrel with a diameter of .750" or .936 at the gas port.
Hard coat Anodized Black.
Select barrel diameter below
|
|
|
|
|
|
|
A1 Front Sight Tool
A1 Front & Rear Sight Adjusting Tool, Steel, 5 prong.
A1 Sight Tool.
|
|
|
|
|
|
|
A2 Sight Tool
A2 Front Sight Adjusting Tool, 4 prong, Steel. A2 Sight Tool.
|
|
|
|
|
|
|
DCM NM Front Sight Post
This front sight post has a thinner front blade. Round. Approx. .050 diameter.
|
|
|
|
|
|
|
Extended Front Post
Extended length front sight post for detachable carry handle & detachable rear sight assembly. Approximately .030 longer post than the standard A2 front sight post (.070 wide)
Four sides square. (4-Prong Sight Tool-A-1 Needed)
|
|
|
|
|
|
|
Hooded Aperture Sight
DPMS Hooded Aperture sight with a .040 diameter peep hole. 8620 steel, interchangeable with your A2 rear sight assembly.
|
|
|
|
|
|
|
NM Rear Apertures .046 and .200 dia.
|
|
|
|
|
|
|
DPMS NM Rear Sights 1/4 min. Windage 1/2 min. Elevation Choice of Aperture Size
|
|
|
|
|
|
|
NM Rear Apertures .040 and .030 dia.
|
|
|
|
|
|
|
NM Rear Apertures .052 and .200 dia.
|
|
|
|
